13.56MHZ HF RFID Embedded Reader Modules-JMY5051H IIC&UART Interface Antennas Connection 50ohm Coaxial Cable

JMY5051H is the second generation product based on JMY505 with UART and IIC serial port. JMY5051H has various functions and supports multi ISO/IEC standard of contactless card. The RF protocol is complex. The designer combined some frequent used command of RF card and then user could operate the cards with full function by sending simple command to the module.
The impedance between RF module and antenna was tuned by impedance analyzer. And then the module has excellent performance and stability.
The module and antenna is split design. They are connecting by a 50ohm coaxial wire whose length is up to 1000cm in good situation. But the best length of the coaxial line is 60cm.

 

• 1. Qualifications
   
• • PCD model: NXP CL RC663
• • Working frequency: 13.56MHz
• • RF standard: ISO14443A, ISO14443B, ISO15693,NFCIP-1, NFCIP-2
• • Anti collision ability: Full function anti collision; be able to process multi-cards; be able to set operate single card only.
• • Auto detecting card: Supported, default OFF. The default state can be set.
• • Power supply: DC 5V (±0.5V)
• • Interface: IIC & UART (selected by SPS pin, recommend to use IIC)
• • Communication rate:
• IIC: Max.200Kbps
• UART: 19200bps / 9600bps / 38400bps / 57600bps / 115200bps
• • Max.command length:
• JCP02 252 Bytes;
• JCP03 510 Bytes;
• JCP04 253 Bytes;
• JCP05 510 Bytes;
• • Interface level: 3.3V (TTL level; 5V tolerance)
• • Power consumption: 130mA
• • Operating distance: 100mm (depending on card and antenna design)
• • Dimension: 42mm*21mm*8mm
• • Weight: About 15g
• • Operating temperature: -25 ~ +85 ℃ (-77 ~ +185°F)
• • Storage temperature: -40 ~ +125 ℃ (-104 ~ +257°F)
• • ISP: Supported
• • RoHS: Compliant
  
   
• 2. Physical Parameter
   
• • Dimension
  
                       
  
  
   
• 3. Pin configurations and Pin outs
  
                       
  
   
• 4. Connection schematic
  
                      
  
   
• 5. Antennas
   
•              Normally, as the size of TX500 series antenna may not meet the actual demands, the antenna needs to be customized,  
               especially in some compact systems. The following information for customization is needed:
               1. Dimension of the antenna PCB;
               2. the position and direction of the antenna outlet and the connector;
               3. the description of the antenna periphery. JINMUYU will design the most proper antenna according to the user’s
               exact requirements.

               We provide many models of antenna. There are some recommended models in the table
  
                          
  
  
   

• 6. Module Function Configuration Table
   

  	JMY5051H
  PCD	RC663
  JCP02 Communication Protocol	●
  JCP03 Communication Protocol	●
  JCP04 Communication Protocol	●
  JCP05 Communication Protocol	●
  MIFARE 1K	●
  MIFARE 4K	●
  MIFARE Ultra Light	●
  MIFARE Ultra Light C	●
  MIFARE Mini	●
  MIFARE DESfire (Step Commands)	●
  MIFARE Plus	●
  T=CL TYPE A	●
  SR176	●
  SRI512	●
  SRI1K	●
  SRI2K	●
  SRI4K	●
  SRIX4K	●
  T=CL TYPE B	●
  I.CODE 1	●
  I.CODE SLI	●
  I.CODE SLI-S	●
  TI Tag-it Series	●
  ST LRI Series	●
  NFC Active Initiator	-
  NFC Active Target	-
  NFC Passive Initiator	●
  NFC Passive Target	-
  NFC Card	-

   
  
  
   
• 7. Communication Protocols
   
•        The physical interfaces of module are various. But the data link layer protocols are in accordance with JCP02, JCP03, JCP04 
         and JCP05. Please reference "JMY600 Series IC Card Module General Technical Manual".

  For convenience to test the Module, we supply PC software: TransPort to users.

  We have interface program source code to help users also. They are KELL projects in C51 or ASM51 format.

  Please log in our website: www.jinmuyu.com to download or mail to lilly.tsheng@jinmuyu.com to obtain the resources.